Small travel size for quick repairs or small projects!
E6000 Adhesive - Medium Viscosity Clear 0.18 oz Tube E-6000® comes in a 0.18 oz tube that contains thick, permanent bonding adhesive. This small size is perfect for travel or small projects! It’s a tough, flexible and highly versatile rubber based compound that exhibits exceptional adhesive, contact adhesive and sealant qualities. It’s washer and dryer safe. E6000 provides adhesion strength and versatility not found in silicones and rubber cements. Its strength in adhering metals, glass, rubber and plastics makes it a universal vehicle maintenance and repair solution. Also, because it is self-leveling, E6000 may be used as potting material in electrical and computer applications. The medium viscosity is perfect for application of rhinestones on flip-flops where you need some help keeping the adhesive from running off the straps. COMMONLY USED SURFACE-TO-SURFACE APPLICATIONS ARE: * Rhinestones * Glass * Clay Pottery / Rocks / Sea Shells * Beads / Fabric * Ceramic / Wood * Glass / Metal DIRECTIONS & TIPS FOR USING E-6000®: 1. Apply E-6000® directly to each surface to be bonded. Note: E-6000® hardens by solvent evaporation and forms an immediate bond that is difficult to reposition after both adhesive coated surfaces are placed in contact with each other and sufficient pressure is exerted to establish full contact. SPECIAL TIPS: To extend life of product, be sure cap is secured back to original position. Use a toothpick as a disposable applicator for very small applications such as beading. Remove, recap and allow plastic nozzle to dry. Remove dried product from nozzle by pulling out through threaded end and reuse nozzle. TEMPERATURE RECOMMENDATIONS/LIMITATIONS: Performs best when applied at 70 to 85 degrees F. When fully cured, product can withstand temperatures between –40 and 150 degrees F. GAP FILLING ABILITY: Up to ¼-inch CLEAN UP & REMOVAL RECOMMENDATIONS: Uncured E-6000® can be cleaned by using small amounts of solvents such as Acetone, Tolulene or Naphtha. Cured E-6000® requires scraping or cutting away product with sharp knife and use of mineral spirits (i.e. gasoline, lighter fluid, lacquer thinner) to soften product. CAUTION ADVISORIES OR SAFETY RECOMMENDATIONS: Use E-6000® in a well ventilated area. E-6000® may damage finished surfaces. Avoid prolonged contact until E-6000® is completely dry. Do not dry clean. Always test material samples prior to use on an original project where reversibility is important.
E-6000® comes in a 0.18 oz tube that contains thick, permanent bonding adhesive. This small size is perfect for travel or small projects! It’s a tough, flexible and highly versatile rubber based compound that exhibits exceptional adhesive, contact adhesive and sealant qualities. It’s washer and dryer safe. E6000 provides adhesion strength and versatility not found in silicones and rubber cements. Its strength in adhering metals, glass, rubber and plastics makes it a universal vehicle maintenance and repair solution. Also, because it is self-leveling, E6000 may be used as potting material in electrical and computer applications. The medium viscosity is perfect for application of rhinestones on flip-flops where you need some help keeping the adhesive from running off the straps.
COMMONLY USED SURFACE-TO-SURFACE APPLICATIONS ARE: * Rhinestones * Glass * Clay Pottery / Rocks / Sea Shells * Beads / Fabric * Ceramic / Wood * Glass / Metal DIRECTIONS & TIPS FOR USING E-6000®: 1. Apply E-6000® directly to each surface to be bonded. Note: E-6000® hardens by solvent evaporation and forms an immediate bond that is difficult to reposition after both adhesive coated surfaces are placed in contact with each other and sufficient pressure is exerted to establish full contact. SPECIAL TIPS: To extend life of product, be sure cap is secured back to original position. Use a toothpick as a disposable applicator for very small applications such as beading. Remove, recap and allow plastic nozzle to dry. Remove dried product from nozzle by pulling out through threaded end and reuse nozzle. TEMPERATURE RECOMMENDATIONS/LIMITATIONS: Performs best when applied at 70 to 85 degrees F. When fully cured, product can withstand temperatures between –40 and 150 degrees F. GAP FILLING ABILITY: Up to ¼-inch CLEAN UP & REMOVAL RECOMMENDATIONS: Uncured E-6000® can be cleaned by using small amounts of solvents such as Acetone, Tolulene or Naphtha. Cured E-6000® requires scraping or cutting away product with sharp knife and use of mineral spirits (i.e. gasoline, lighter fluid, lacquer thinner) to soften product. CAUTION ADVISORIES OR SAFETY RECOMMENDATIONS: Use E-6000® in a well ventilated area. E-6000® may damage finished surfaces. Avoid prolonged contact until E-6000® is completely dry. Do not dry clean. Always test material samples prior to use on an original project where reversibility is important.
Price: $1.29